I have to tell you, I thought it would be more of a sweet bread. Remove from oven and let cool for 5 minutes before removing from the pan. Where measurement conditions have not been specified precisely, the conditions used were as follows: supply voltage 24 V DC, ambient temperature +20 ℃ +68 ℉, sampling rate 500 μs, average number of samples: 1024, measurement center distance, object measured is made of white ceramic and analog measurement values.9. between all supply terminals connected together and enclosureĮnvironmental resistance : Vibration resistanceġ0 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X,Y and Z directions for two hours eachĮnvironmental resistance : Shock resistanceĥ00 m/s 2 acceleration (50 G approx.) in X,Y and Z directions three times eachġ4-core cabtyre cable with connector, 0.5 m 1.640 ft longĮxtension up to total 20 m 65.617 ft is possible with optional cable. or less.Ģ0 MOhm, or more, with 250 V DC between all supply teminals connected together and enclosureġ,000 V AC for one min. (Note) The fluctuation by ambient illuminance is ± 0.1 % F.S. Incandescent light: 3,000 liter x or less at the light-receiving face 10 to +45 ℃ +14 to +113 ℉ (No dew condensation allowed), Storage: -20 to +60 ℃ -4 to +140 ℉Įnvironmental resistance : Ambient humidityĮnvironmental resistance : Ambient illuminance Orange LED lights up when this product cannot measure because of insuffienct or excessive light intensity.Įnvironmental resistance : Ambient temperature Green LED (lights up during laser emission) In case PNP output is selected, Function varies according to the time external power + is connected.īaud rate: 9,600/19,200/38,400/115,200/230,400/460,800/921,600 bpsĭata length 8 bit, Stop bit length 1 bit, Without parity check, BCC check, Termination code: CR In case NPN output is selected, Function varies according to the time 0 V is connected NPN. Zero set, zero set off, reset, memory switching, teaching, saving, and laser control according to the input time. PNP output operates when external power + is connected and PNP is set. NPN output operates when 0V is connected and NPN is set. PNP open collector output operates when 24 V DC is connected. NPN open collector output operates when 0 V is connected. Output (OUT 1, OUT 2, OUT 3) : Short circuit protection Opened when the amount of light is insufficient. Output (OUT 1, OUT 2, OUT 3) : Output operation Residual voltage: 2.8 V or less (at 50 mA of source current) Residual voltage: 2 V or less (at 50 mA of sink current) Applied voltage: 3 to 24 V DC (between output and 0 V) Selectable NPN transistor open-collector or PNP transistor open-collector Judgment output or alarm output (Setting can be selected.) Output range: 3.2 to 20.8 mA (normal), 21.6 mA (alarm) Output range: 0 to +10.5 V (normal), 11 V (alarm) Sensing point itself, then the results may be affected.Ģ4 V DC ± 10 % including ripple 0.5 V (P-P) There is a slight leakage of light outside the normal spot diameter and if the periphery surrounding the sensing point has a higher reflectivity than the These values were defined by using 1/e 2 (13.5 %) of the center light intensity. (Note) This beam diameter is the size at the measurement center distance. output: 1 mW (Peak emission wavelength: 655 nm 0.026 mil) 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).), Laser Notice No. Red semiconductor laser, Class 2 (IEC / JIS / FDA (Note:This product complies with. Specifications and design of the products are subject to change without notice for the product improvement.
0 Comments
Leave a Reply. |